Preparing Your Site for a Native Seed Mix

Site preparation Is the most important step for a successful native seed mix installation. The objective is to create the cleanest seedbed possible, and deplete the seed bank as much as possible, to give your native seed mix the best possible start.  There are several methods that could be used, but these four are the most common. Find the one that's right for your site:

SOD CUTTING


If you’re converting a traditional lawn to native seed mix, the sod cutting preparation method can be used on existing lawns of turf grass that contain few-to-zero weeds.  You’ll need a sod cutter to remove the top two to three inches of grass and soil. After clearing the sod you’ll need to lightly till the cleared area before planting into a prepared bed. Light tilling could be accomplished with a shovel if the site is small, otherwise, a tiller attachment can be used with some riding mowers/lawn tractors.  If the soil under the sod is heavy clay with little or no topsoil, amendment with two inches of loose, weed-free loam is advisable to create a good germination medium.

SMOTHERING / SOLARIZATION


Smothering is an organic site preparation method used on existing lawns that are weedy. This method is best for small sites of 1000 square feet or so, and it takes a full season to complete. You can use black plastic sheeting, clear plastic sheeting (Solarization), or cardboard.  Smothering and solarization use high temperatures to kill off existing vegetation, and prohibit seeds from germinating in the topsoil. The heat reduces seed viability and helps reduce the seedbank. Depending on the seedbank at your site, some perennial weeds may persist. Clear plastic (Solarization) is used for sites in full sun, that are flat and dry.  Black plastic sheeting or cardboard can be use in a variety of settings.

First, mow the site in the spring (April or early May). Rake off or bag the cut vegetation. If you use a plastic sheeting, dig a trench about 4” Deep around the site perimeter then cover the entire site, including the trench, with the planting sheeting.  Fill in the trenches with soil to anchor the sheeting. Alternatively, if you'd rather not dig a trench, you can anchor the edges with rocks, bricks or large landscape pins. If you choose to use cardboard, you will need to overlap the pieces and anchor the cardboard securely in place. We have seen wood mulch used to anchor card board, however, that can require a large amount of mulch that will need to be removed, and is not needed after the smothering is completed.

Leave the plastic or cardboard in place from spring until fall. Remove the plastic in late fall, rake off any dead vegetation, and lightly till the surface to prepare the seed bed. Till the surface, but do not till too deep. You will need at least an inch of finely tilled surface for good seed-to-soil contact in the seed bed.

MECHANICAL TILLING/CULTIVATION


A good organic alternative to herbicides for large sites or lawn or agricultural sites, the tilling method requires a full growing season to complete and is used on even sites that are not subject to erosion. 

The idea with mechanical preparation is to constantly disturb the topsoil to encourage plants to grow from the seed bank. Once they grow, they get cut back and eventually you exhaust the seed bank.  You can use a chisel plow, cultivator, a rototiller, or similar implement that reaches down at least six inches into the soil to disturb the roots of undesirable plants.

If the site has tall standing vegetation, mow in early spring (April) and remove the cut material. Cultivate to a depth of four to five inches every two to three weeks from spring through fall. When you see new vegetation emerging and reaching 3 – 6 inches, it is time to disk or till, again. Seeding will occur late in the fall at the start of the dormant period, or the following spring.

With repeated tillage, root reserves are eventually depleted and the plants die. The strategy is to allow the plants to regrow three to six inches tall after each tillage event. Tilling at this point, preferably on a hot sunny day, destroys their new growth, damages their roots, and dries the plants out. A disc does not usually reach sufficiently deep into the soil, and does not bring up the roots to the soil surface where they can be dried out. A cultivator or tiller can be set to go six to eight inches deep, brings up the roots and exposes them to the sun. A chisel plow works better than a moldboard plow as it reaches deep down into the soil. A moldboard plow can be used to work the field up the first time, but cannot be used repeatedly due to its inability to operate in the furrows that it creates during the initial plowing.

HERBICIDE


If you choose to use herbicides, always use them carefully and in accordance with manufacturer’s directions. Hiring a professional agricultural herbicide applicator for larger sites is a good idea. They will  have the proper equipment, are licensed and trained.  

Our PDF 'Site Preparation and Seeding methods' covers the herbicide application process in detail for different types of sites: Agricultural fields, lawns, weedy old fields, and new construction.